Access point

What is an Access Point?

An  access point is a device that creates a wireless local area network, or WLAN, usually in an office or large building. An access point connects to a wired router, switch, or hub via an Ethernet cable, and projects a Wi-Fi signal to a designated area. For example, if you want to enable Wi-Fi access in your company’s reception area but don’t have a router within range, you can install an access point near the front desk and run an Ethernet cable through the ceiling back to the server room.

Network access point Definition

A Network Access Point was a public network exchange facility where Internet service providers connected with one another in peering arrangements. The NAPs were a key component in the transition from the 1990s NSFNET era to the commercial Internet providers of today. 

Network Access Point (NAP) is a set of operating system components that provide a platform for protected access to private networks. The NAP platform provides an integrated way of evaluating the system health state of a network client that is attempting to connect to or communicate on a network and restricting the access of the network client until health policy requirements have been met.

NAP is an extensible platform that provides an infrastructure and an API set for adding components that store, report, validate, and correct a computer’s system health state. By itself, the NAP platform does not provide components to accumulate and evaluate attributes of a computer’s health state. Other components, known as system health agents (SHAs) and system health validators (SHVs), provide network policy validation and network policy compliance.

(NAP) is one of several major Internet interconnection points that serve to tie all the Internet access providers together so that, for example, an AT&T user in Portland, Oregon can reach the Web site of a Bell South customer in Miami, Florida. Originally, four NAPs – in New York, Washington, D.C., Chicago, and San Francisco – were created and supported by the National Science Foundation as part of the transition from the original U.S. government-financed Internet to a commercially operated Internet. Since that time, several new NAPs have arrived, including WorldCom’s “MAE West” site in San Jose, California and ICS Network Systems’ “Big East.”

This article gives a small brief about the various types of Wireless Access Points available in the market – Single radio, dual radio, external antennas, internal antennas, a, b/g, b/g/n technologies, support for mesh networking, stand alone, controller based access points and support for multiple services.


Types of the Wireless Access Point

Nowadays, Wifi 6 access points are more and more popular than before. According to the generations of WiFi, we have known there are WiFi 6 APs, WiFi 5 APs, etc., but do you know how many types the Wireless APs provide?

In this post, let’s discuss the types of APs.

  1. Divided by Applications: Commercial AP and Enterprise AP

Commercial AP: Suitable for commercial environments, such as hotels, guesthouses, KTVs, supermarkets, restaurants and other places, which require aesthetics and have many access users. We know there are Hospitality Access Points, which is designed for hotels, such as Aruba 500H Hospitality Wifi 6 access points

Enterprise-level AP: It is suitable for use in large enterprises, companies and other places, and has high security requirements. Commercial APs can also be used in enterprises. Many manufacturers provide this kind of AP, like Cisco AP, Huawei AP, Aruba AP RUckus AP, etc.

access point placement in an office
  1. Divided by installation method: In-wall AP and Ceiling AP

In-wall AP: In-wall AP is sometimes called panel type. It needs to be embedded in the wall during installation, so it is generally necessary to reserve slots. This kind of AP has a compact appearance, and its rate is generally 150Mbps or 300Mbps.

Ceiling AP: It can be directly attached to the wall or ceiling during installation, without entering the wall. The appearance is variable, there are single-frequency and dual-frequency, and the transmission rate is generally higher than that of the wall-mounted AP.

ceiling ap
  1. Divided by frequency band: Single-frequency AP and Dual-frequency AP

Single-frequency AP: Generally refers to a wireless AP that supports 2.4G, and the transmission rate is generally between 150Mbps and 450Mbps, but the anti-interference ability of single-frequency AP is relatively weak.

Dual-band AP: refers to a wireless AP that supports 2.4G and 5.8G at the same time. When in use, the mobile terminal can search for two WiFi signals, with a higher transmission rate and a larger amount of equipment.

  1. Divided by controller needed: Standalone AP and Controller Needed AP

Standalone AP: It’s mostly used in high-demand environments. To achieve bai certification, authentication servers or switches supporting authentication functions are generally required. This AP requires a dedicated wireless controller, and can be used only through the configuration of the wireless controller. It cannot be configured by itself and is suitable for large-scale wireless deployment. Some Cisco access points are needed Cisco wireless controllers.

Controller Needed AP is mostly used in homes and small networks, with relatively complete functions. Generally, a single device can implement access, authentication, routing, VPN, address translation, and even firewall functions.

cisco ap and controller
  1. Divided by Network standards: IEEE 802.11ac, IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.11ax, etc.

By different standards, the access points will provide different frequency band.

GenerationWiFi 4WiFi 5WiFi 6W-f-i 6E
Released Date2009201320182020
Frequency band2.4GHz, 5GHz5GHz2.4GHz, 5GHz4GHz, 5GHz, and 6GHz
  1. Divided by Environment: Indoor AP and Outdoor AP

In order to adapt to harsh environments, such as dealing with severe weather, high temperature climate, extreme cold weather, and various difficult environments, outdoor access points need to be designed to be more robust and durable, signal requirements are also higher, as well as the signal range that needs to be transmitted wider. Relatively safe indoor environment, so that indoor access points do not need to provide these functions.


Do you have other types of AP? Welcome to leave your idea.


¤Network Access points are the basic elements of a wireless network – They scan for the wireless devices in its range and all the neighbouring Wi-Fi systems connect to the Access Point to communicate with the network.
¤ Access points offer a standard for connectivity – a, b/g, b/g/n which are all ratified by IEEE so that the Wi-Fi systems from various vendors can connect to the network.
¤ Access points connect to PC’s, laptops, PDA’s, mobiles, Wi-Fi phones, Wi-Fi Cameras, Wi-Fi display management systems and a host of other devices that work on the Wi-Fi standard.
¤ Access points can also scan the network for wireless threats and attacks.

Please note: Even thought Access Points provide wireless access to clients, they are themselves hooked to the network through Cables (Cat 5E/ Cat6) and hence the back bone of the wireless networks are most often wired. But there are exceptions.

Single Radio/ Dual Radio Access Points:

Some Access Points come with a single radio – They work in either IEEE 802.11a or b/g – This can be selected. Most of them work in the b/g standard as most of the network adaptors follow that standard. But some Access Points come with a dual radio option. One radio works in IEEE 802.11a and the other works simultaneously in IEEE 802.11b/g or even IEEE 802.11 b/g/n. Dual radio Access Points are useful for mesh networking, giving access to laptops containing only 802.11a network adaptors and also for wireless intrusion scanning/ prevention.

External Antennas/ In-built Antennas:

Most of the Access Points come with built-in antennas with a certain gain specified by the manufacturer. While they give a decent coverage, there may be certain applications where the no. of users may be small but the area to be covered may be large – like a lawn/ park. In these circumstances it is better to use Access Points with external antenna provisions as the external antennas come with a higher gain and can boost the signal strength to a higher distance. But in both the cases the bandwidth supported by an access point is standard.

IEEE Standard supported: 802.11a,b,g,n:

IEEE has standardised the wireless access protocols so that multi vendor systems can connect and talk to each other through Wi-Fi.

IEEE 802.11b supports upto 11 Mbps but IEEE 802.11a and g support upto 54 Mbps on a shared platform. IEEE 802.11n currently (in draft) supports upto 300 Mbps and in future would support 600 Mbps per Access Point (Please note: As the number of PC’s that connect to the AP’s increase, the bandwidth gets shared between them and the numbers are under ideal conditions, and practically achieved bandwidth may be half of what is specified per AP).

The standard Access Points should support upto 30 meters indoor and slightly more than double of that in outdoor (Although in practical applications there are many AP’s deployed within 30 meter distances based on the number of users and the bandwidth they require).

So, per radio, the Access Points can support either IEEE 802.11 a or IEEE 802.11b/g/n (As they operate at different frequencies) and based on the protocol supported by the Access Point, the bandwidth supported per AP would vary.

Practically, 15-20 users are recommended to simultaneously connect per AP in order to get a decent throughput.

Support for Mesh Networking:

Certain vendors support mesh networking in certain dual radio Access Points. While one radio of the AP connects to the clients, say in 802.11b/g, the other radio establishes a point to point back end connectivity to the neighbouring Access Point, say in 802.11a (Which is similar to this one) and hence eliminate the data cable connecting to the AP(but not the power cable). Though the AP’s can connect to each other in this fashion, with every hop the available bandwidth to the last Access Point(from the wired network) is halved. So, farther the AP to the wired network, lesser is the bandwidth.

Controller based Access Points and Stand-Alone Access Points:

Though this topic could be a post in itself, right now it is sufficient to mention that there are certain access point which operate independently and there are some more which operate only with a controller and there are some others which operate on a stand-alone basis and could be converted to a controller based one at a later stage.

If the wireless network is to be established over a small distance – single floor and 15 devices kind of an application, stand alone Access Points could suffice. But higher the distance and more the area to be covered, it makes more sense to go for the controller based Access Points as the management of the AP’s is easier through the controller and from a central point. Imagine having a huge campus and hundreds of Access Points. If a new user joins or a new upgrade is released for the AP, it is very difficult to update each AP individually. And controllers perform a lot more functions that are critical for maintaining a wireless network and enabling applications in it.

Support for Multiple Services:

Certain services like Wireless Intrusion Prevention (A method of scanning the whole area to locate for wireless threats and intrusions) can be performed simultaneously by the Access Point while giving network access (Dual Radio types). But certain vendors have a separate specialised Access Point to scan the network for identifying intrusions.

Most of the Enterprise Access Points support POE (Power over Ethernet – A feature where the electrical power required for the AP is sent along with the data via the Cat5E/ Cat6 network cable itself). Perhaps there could be some home AP’s that don’t support this feature.

What are the functions of a network access point?

A network access point is a device that creates a wireless local area network, or WLAN, usually in an office or large building. An access point connects to a wired router, switch, or hub via an Ethernet cable, and projects a Wi-Fi signal to a designated area.


More User Access

While a wireless router can only support about 10-20 users access at a time, a wireless access point can allow over 50 or even hundreds of users access. The wireless AP has a much stronger ability to send and receive signals, which enables such high usage. If you are considering wireless Internet for a large area, using a wireless access point gives you a better guarantee of efficiency. 

Broader Transmission Range

A wireless router’s signal transmission can cover about a dozen meters before its signal is lost. A wireless access point, however, can cover up to 100-300 meters. The broad range is excellent for businesses that cover large office spaces or multiple buildings. With a wireless access point, employees can communicate across buildings and larger distances. 

Flexible Networking

The networking mode of a wireless router is low flexibility and relatively single. A wireless access point has a variety of modes to choose from, to encourage flexible usage. These modes include Simplex AP, Wireless Client, Wireless Bridge, Multi-point Bridge, and more. 

Multi-Access Point Interconnection

Multi-AP applications are often found in businesses. The coverage of a single AP may be too limited for a large enterprise, so to extend the coverage of wireless networks, a multi-AP interconnection will be used. The multi-AP interconnection allows clients to roam within the network seamlessly. 

If this article pleases you drop your comment


Author: refuge_2020

Leave a Reply

Your email address will not be published. Required fields are marked *